-
When to use this checklist
-
Step 1: Define the environment and compliance requirements before you talk product
-
Step 2: Request photometric and electrical files, not just marketing copy
-
Step 3: Check construction and thermal design like you're going to install it yourself
-
Step 4: Audit exit sign compliance before you choose a wholesale supplier
-
Step 5: Run an incoming QC sample, not a paperwork check
-
Step 6: Lock down OEM and customization guardrails
-
Step 7: Put warranty, lead time, and spares in the contract
-
Common mistakes to avoid
When to use this checklist
Use this if you're a distributor, contractor, or OEM buyer placing a bulk order for industrial or commercial LED lighting. It's built for mixed orders: a pallet of Dialight LED high bay fixtures, a container of bulk recessed lighting, a ceiling light OEM run, and a batch of exit signs you need to choose for wholesale. I review every fixture and spec sheet before it reaches our customers—roughly 300 SKUs per quarter. In 2024, I rejected 18% of first deliveries because the paperwork said one thing and the box said another. That's not a vendor problem. That's a process problem.
My initial approach was wrong. When I first started sourcing LED high bays, I assumed if the lumens matched, everything else was interchangeable. A few failed inspections later, I learned that lumens are just one line on a spec sheet. The checklist below is what I actually use now. It has 7 steps. Don't skip step 4—it's the one most buyers miss.
Step 1: Define the environment and compliance requirements before you talk product
Don't start with 'I need a high bay.' Start with where it's going. A Dialight LED high bay for a dry warehouse has different requirements than a Dialight SafeSite LED high bay for a wet, corrosive, or hazardous area. Write down:
- Location: indoor, outdoor, damp, wet, dusty, corrosive, high-ambient, hazardous classified.
- Required listings: UL, cUL, DLC, NSF, IP rating, NEMA rating, Class/Division if applicable.
- Emergency egress requirements: NFPA 101 and local AHJ rules for exit signs and emergency lighting.
For exit signs, UL 924 is the baseline. It covers emergency lighting and power equipment, including exit signs. If a wholesale exit sign isn't UL 924 listed, that's a red flag. Not a maybe. A no-go.
For high bays, check DLC listing if rebates matter. For hazardous areas, verify the exact Class and Division or Zone rating. Don't assume a fixture is explosion-proof because the catalog says 'industrial.'
Step 2: Request photometric and electrical files, not just marketing copy
This is where most first deliveries fail. Ask for IES files, LM-80 and TM-21 data, driver datasheets, and a production sample. For a Dialight LED high bay, compare the published lumen output, wattage, CCT, CRI, beam angle, and color consistency. For a ceiling light OEM program, ask for driver brand, surge protection rating, power factor, THD, and dimming compatibility.
I assumed 'same specifications' meant identical results across vendors. Didn't verify. Turned out each vendor had slightly different interpretations of CCT, beam angle, and 'equivalent' wattage. Now every contract includes photometric file requirements and a signed spec sheet.
If you're buying bulk recessed lighting, request a sample from the actual production run. Not a golden sample. Not a lab unit. The production run.
Step 3: Check construction and thermal design like you're going to install it yourself
Open the fixture. Look at the heat sink, driver compartment, gaskets, and wiring. For high bays, ask about ambient temperature rating and lumen maintenance at that temperature. For bulk recessed lighting, check trim thickness, junction box compatibility, IC rating, airtight rating, and whether the driver is serviceable.
For ceiling light OEM, confirm the driver is not potted in a way that makes field replacement impossible. That's a deal-breaker for many B2B customers. They don't want to replace a whole fixture because a driver failed.
Also check finish consistency. If you order 500 bulk recessed lights and the white trim doesn't match across cartons, your customer notices. They may not say 'batch variance.' They say 'this looks cheap.'
Step 4: Audit exit sign compliance before you choose a wholesale supplier
How to choose exit sign for wholesale: start with the listing, not the price. UL 924 listing is the minimum. Then verify:
- 90-minute emergency runtime at the specified load.
- Test switch and status indicator.
- Battery type and replacement availability.
- Chevron direction options and field-selectable or fixed configuration.
- Damp or wet location listing if needed.
- Compliance with NFPA 101 and local amendments.
If I remember correctly, we had a batch of exit signs where the housing was listed but the battery wasn't. The vendor said it was 'within industry standard.' We rejected the batch, and they redid it at their cost. Now every exit sign contract includes battery model and runtime test requirements.
Don't assume the cheapest wholesale exit sign is the same as the one in the catalog photo. The photo might show a premium housing. The carton might show a thinner plastic and a different battery.
Step 5: Run an incoming QC sample, not a paperwork check
When the shipment arrives, pull a sample. I use a 10% sample for new vendors and 5% for repeat vendors with good history. Test:
- Lumen output and wattage draw on a sample basis.
- Color consistency across fixtures in the same batch.
- Flicker and driver compatibility with your controls.
- Finish, label placement, and packaging.
- Emergency runtime for exit signs and emergency fixtures.
We ran a blind test with our installers: same high bay footprint, one with a premium finish and one with a budget finish. 68% identified the premium finish as 'more professional' without knowing the difference. The cost increase was around $4 per fixture. On a 2,000-unit run, that's $8,000 for measurably better perception. Bottom line: quality is brand image.
Step 6: Lock down OEM and customization guardrails
For ceiling light OEM, get everything in writing before tooling starts. Who owns the tooling? What is the MOQ? Who approves label and packaging artwork? Which driver brand is locked? What happens if the driver is discontinued? What is the change-control process?
For bulk recessed lighting, define color temperature tolerance, trim finish, and packaging drop-test requirements. For Dialight SafeSite LED high bay orders, confirm the exact factory certification and labeling for your region. A fixture can be right for one country and wrong for another.
Plus, ask for a pre-production approval sample. Sign it. Keep it. That signed sample is your reference when the first mass-production batch arrives.
Step 7: Put warranty, lead time, and spares in the contract
The lowest quoted price often isn't the lowest total cost. Total cost includes:
- Base unit price.
- Setup or tooling fees.
- Shipping and handling.
- Rush fees.
- Reprint or replacement costs for defects.
- Field labor for failures.
Define the warranty period, RMA process, replacement lead time, and spare parts availability. If a Dialight LED high bay driver fails, how fast can you get a replacement? If an exit sign battery fails in year two, who pays?
If I remember correctly, we had a shipment delayed by about two weeks because the driver was on allocation. That delay cost us a $22,000 project and a very unhappy contractor. Now we require a written lead-time commitment and a backup driver option for critical orders.
Common mistakes to avoid
- Assuming 'same specs' means identical performance. It doesn't.
- Skipping the local AHJ for exit signs and emergency lighting. NFPA 101 is the floor, not the ceiling.
- Buying bulk recessed lighting on price alone. Color and trim consistency are what customers see.
- Treating a ceiling light OEM sample as the final product. Approve a production sample.
- Ignoring packaging. A great fixture that arrives dented is a bad fixture.
- Forgetting that quality is a brand decision. The first thing a contractor sees is the box, the finish, and the label. That's your brand, not the factory's.
Use this list before your next PO. It won't make sourcing easy, but it will make the surprises less expensive.